SM智能防爆加熱器
| II 2G Ex d IIC T4 or T3 KEMA 01ATEX2124X II 2D Ex tD A21 IP66 T 135 oC or T 200 oC IECEx DEK 11.0017 CE 0344 Voltage: 110-240VAC/DC 電壓：110-240 伏交流電或直流電 Power: 250-25 Watt & 500-50 Watt (marked 0) 能量：250-25瓦和500-50（標記為0） All Models with * = 0 and 1, are T3 classified 所有帶有* = 0和1的型號，都屬于T3類 All Models with * = 2, 3 or 4 are T4 classified 所有帶有* = 2,3或4的型號，都屬于T4類 Certified ambient temp. range: -60o C… +90o C 經過證實的外圍溫度范圍：- 60°C 至+ 90°C English: Installation and maintenance instructions for Explosionproof electrical SMART Heaters. 英語：防爆電氣智能加熱器的安裝和維護說明 1. The heaters are for fixed installations and due considerartion should be given to the information on the nameplate and/or eventual “special requirements”mentioned in the certificate. 加熱器是用于固定安裝的，適當?shù)目紤]應當被添加到銘牌的數(shù)據(jù)中，且/或最終在證書上提到“特殊需求”。 2. The apparatus may only be used on the basis of the way it protected against ignition, the gasgroup and the temperature class (see above temp. classificaton/type), for which it is certified. 2、設備僅僅可以在它能受到保護以防止引燃、氣體集中和溫度等級（詳看上面的溫度等級/類型）的方式下使用，因為它是經過認證的。 3. The heaters are standard equipped with a braided silicone cable. The yellow/green wire -3- is connected to the internal ground. 3、加熱器標準地配有編織硅膠 電纜。黃色/綠色的線-3-就是連接內部地線的。 The wires -1- and -2- have to be connected to the mains. 線-1-和線-2-必須連接到總管道上。 The cable have to be connected to the terminals inside an ATEX certified junction box. 電纜必須連接到經過認證的分線盒ATEX 內部的終端上。 The nameplate indicates the standard voltages. 銘牌顯示了標準的電壓。 If non braided cables are used, they must be protected against mechanical damages (-X-) 4、如果使用非編織電纜，它們一定會受到保護以防機械損傷(-X-)。 5. After the user switches-on the apparatus, they must be protected against direct contact with the warm-surface. A WARNING STICKER has been fixed onto this surface. 5、如果使用者開啟了設備，他們一定會受到保護以防直接接觸溫熱的表面。一則警示標語已經被貼在了表面上。 After swiching-off the heater the surface slowly reduces in temperature. The user must be aware of this 加熱器被關掉后，表面溫度會慢慢降下來，使用者一定要注意到這一點。 Product is according the standards:產品遵循以下標準： EN 60079-0: 2006 IEC 60079-0 : 2004 EN 60079-1: 2004 IEC 60079-1 : 2007 EN 61241-0: 2006 IEC 61241-0 : 2004 EN 61241-1: 2004 IEC 61241-1 : 2004 Datum: 02-05-2011 日期：02-05-2011 SM-*A, rev. 3 ENG SM-*A, rev. 3 ENG The standards indicated above are no longer harmonised. A review against the standards listed below, which are harmonised, identified no significant changes to this equipment. The previously applied standards continue to represent the ‘state of the art’. 以上顯示的標準不再進行調整。進行復審后，我們對標準又進行了以下的調整，經證實對儀器不會產生重大影響。之前應用的標準繼續(xù)代表其“目前發(fā)展水平”。 EN 60079-0: 2009 EN 60079-1: 2007 EN 60079-31: 2009 防爆加熱器 防爆電加熱器 |
