效率
簡易
精確
創新
一、塑料擺錘沖擊試驗機參數
沖擊能量 Maximum impact energy | 簡支梁(ISO/GB) 25J Simply supported beam (ISO / GB) 25J |
簡支梁(ASTM) 21.6J Simply supported beam (ASTM) 21.6J | |
懸臂梁22J Cantilever beam 22J | |
角度分辨率 Angular resolution | 0.045º |
簡支梁(ISO/GB)技術參數：
沖擊速度 impact speed | 2.9m/s（5J）、3.8m/s（＞5J） |
預揚角 Pre-elevation | 107 º（5J）、148 º（＞5J） |
擺軸中心至試樣中心的距離 | 330mm（5J）、398mm（＞5J） |
沖擊刀夾角 Striket Angle | 30º |
沖擊刀圓角半徑 Striket fillet radius | 2mm |
支座圓角半徑 Bearing fillet radius
| 1mm |
支座前角 Abutment anterior angle | 5º |
支座后角 Abutment relief angle | 10º |
支座跨距 distance between anvil tips | 62mm |
試樣類型及尺寸（長×寬×厚） Sample type and size (length × width × thickness) | 80×10×4mm |
簡支梁(ASTM)技術參數：
沖擊速度 impact speed | 3.46m/s |
預揚角 Pre-elevation | 148 º |
擺軸中心至試樣中心的距離 The distance between the center of the pendulum shaft and the center of the sample | 330mm |
沖擊刀夾角 Impact blade angle | 45º |
沖擊刀圓角半徑 Impact blade arc radius | 3.17mm |
支座圓角半徑 Bearing fillet radius
| 3.17mm |
支座跨距 distance between anvil tips | 101.6mm |
試樣類型及尺寸（長×寬×厚） Sample type and size (length × width × thickness) | 127mm×12.7mm×3.17mm |
127mm×12.7mm×6.35mm | |
127mm×12.7mm×12.7mm |
懸臂梁技術參數：
沖擊速度 impact speed | 3.5m/s |
預揚角 Pre-elevation | 148 º |
擺軸中心至試樣中心的距離 The distance between the center of the pendulum shaft and the center of the sample | 330mm |
刀刃圓角半徑 Impact blade arc radius | 0.8mm |
刀刃中心距鉗口上表面 Distance from the center of the blade to the upper surface of the jaw | ISO/GB:22±0.2mm |
ASTM:22±0.05mm | |
試樣類型及尺寸（長×寬×厚） Sample type and size (length × width × thickness) | ISO/GB: 80×10×4mm |
ASTM: 63.5×12.7×12.7mm |
拉伸沖擊技術參數：
沖擊速度 impact speed | 3.8m/s |
預揚角 Pre-elevation | 148 º |
擺軸中心至試樣中心的距離 The distance between the center of the pendulum shaft and the center of the sample | 398mm |
丁字頭質量 T-head mass | 60±1g、120±1g |
試樣厚度 Maximum thickness of specimen | 4mm |
環境溫度 Ambient temperature | 10～35℃ |
設備可選配置：
簡支梁（ISO/GB）擺錘 Pendulum of simply supported beam (ISO / GB) | 5J、7.5J、15J、25J |
簡支梁（ASTM）擺錘 Pendulum of simply supported beam (ASTM) | 5.4J、10.8J、21.6J |
懸臂梁擺錘 Cantilever pendulum | 5.5J、11J、22J |
拉伸沖擊擺錘 Tensile impact pendulum | 7.5J、15J、25J |
簡支梁支座一套 A set of simply supported beam support | (配試樣對中裝置一套、跨距找正塊一個) a Centralizer、 a Span alignment block |
| ASTM：鉗口三對 Three pairs of jaws |
ISO/GB& ASTM：鉗口五對 Five pairs of jaws | |
懸臂梁支座一套 A set of cantilever support | (配對中器一個) A centralizer |
ISO/GB：固定鉗口一個 One regular jaw | |
ASTM：固定鉗口三個 Three regular jaw | |
ISO/GB& ASTM：固定鉗口四個 Four regular jaw |
二、金屬擺錘沖擊試驗機參數規格： Parameters and specifications of metal pendulum impact testing machine:
擺錘能量 Pendulum energy | 150J、300J、450J、750J |
擺錘測量范圍 Pendulum measuring range | 10%-80% |
預揚角 Pre-elevation | 150° |
角度最小分辨率 Angle minimum resolution | 0.025° |
擺錘中心至沖擊點距離 Distance from pendulum center to impact point | 750mm |
沖擊速度 impact speed | 5.24m/s |
沖擊刀刃夾角 Impact blade angle | 30° |
沖擊刀刃圓弧半徑 Impact blade arc radius | R2（GB/ISO） R8（GB/ISO） R8（ASTM） |
試樣支座跨距 Sample support span | 40mm |
試樣規格 Sample specification | 55mm×10mm×10mm |
金屬擺錘沖擊試驗機自動送樣裝置參數：Parameters of automatic sample feeding device of metal pendulum impact testing machine:
裝樣數 The bullet capacity | 30 |
滿足試樣規格 Meet the sample specification | 55 mm*10 mm*10 mm |
55 mm*10 mm*7.5 mm | |
55 mm*10 mm*5 mm | |
定位方式 Location mode | 端面定位 End face positioning |
冷卻溫度 Minimum cooling temperature | -180℃ |
試樣離開冷卻室到被沖斷時間 Time from specimen leaving cooling chamber to being broken | ≤5s |
