間歇開關通斷循環定時器一拖二變頻PWM雙輸出通斷互鎖可調控制器
電機 馬達 風機 風扇 改遙控 改變頻 改PWM 調速 節能 雙輸出 互鎖 間歇開關 通斷循環定時器 一開另一關
應用場景 風機 通風，新風系統 ，生產線 冷卻線 加熱線 ，噴涂，噴淋，LED 燈光控制 閃燈控制 小風扇調速
同步電機調速 等等
NKAC150Y(遙控型)一拖二變頻PWM雙輸出通斷互鎖可調控制器
1 原理 控制輸出端的通斷時間間隔以達到調控輸出功率的目的，所以輸出端電壓與頻率與輸入端相同
PWM=Pulse Width Modulation=調制脈沖寬度調節輸出功率
2 工作過程 兩插腳輸入AC220V 50HZ(內置250V 2A保險)，輸入端與黃色插座輸出相同（無PWM無互鎖）
按遙控器黃標簽風速鍵,黃插座按黃旋鈕PWM輸出，按遙控器紅標簽搖頭鍵,紅插座按紅旋鈕PWM輸出
控制器內部默認： 黃 紅 LED亮滅互鎖 黃 紅 插座通斷互鎖(按遙控器黃紅標簽按鍵有PWM輸出時）
黃LED亮=黃插座通同時紅LED滅=紅插座關斷，黃LED滅=黃插座關斷同時紅LED亮=紅插座通
3 輸入電源AC220V,分別按遙控器黃紅標簽按鍵，黃紅旋鈕PWM設置才有效，黃紅插座才有PWM輸出
額定輸入AC220V (內置250V2A保險)黃插座輸出AC220V 800mA 紅插座輸出AC220V 800mA
在輸入電源AC220V后，黃紅輸出插座在關斷狀態下，單極持續接通，另一極通過電子管高阻關斷
在輸入電源AC220V后，黃紅輸出插座在關斷狀態下，仍然帶電，請忽觸摸插頭插座金屬部分
遙控器要對準遙控接收頭才能有效，遙控有效距離5米 ，
要按遙控器黃標簽按鍵黃插座才有PWM輸出，要按遙控器紅標簽按鍵紅插座才有PWM輸出
自主研發，可定制直流輸入輸出PWM，或大功率PWM，出線長度，國際插腳或插座
NKAC150Y(遙控型) 標準配置
兩扁插腳 輸入AC220V 50HZ (250V 2A保險)
兩扁插座 黃插座輸出AC220V 50HZ 800 mA 紅插座輸出AC220V 50HZ 800mA (包括插座輸出線長度75mm)
控制器不包括插腳插座 尺寸 長98x寬54x高35mm,插腳長35x寬20x高25mm 控制器包括插腳插座重量300g
手持式遙控器 輸入直流DC3V =AAA-1.5V 7號電池 2只
手持式遙控器 包括電池200g 長105x寬40x高15mm
Intermittent switch, on /off cycle loop timer
Application scenario fan ventilation, fresh air system, production line cooling line heating line, spraying, spraying, LED lighting control flashlight control etc
NKAC150Y(remote control)1 input 2 output PWM on/off interlocking controller
1 operational principle The on/off time of the output is controlled by the controller, so the output voltage and frequency are the same as the input terminal. PWM=Pulse Width Modulation Power
2 operational process Input AC230V 50/60HZ(built-in 250V 2A Fuse)，input=Yellow output（no PWM no interlocking）
Press yellow label speed key of the of the remote-controller, the Yellow socket = Yellow knob PWM output, Press red label swing key of the remote controller, the red socket =red knob PWM output.
press remote-controller yellow/red label button when PWM output, Controller interlock default：
Yellow LED brightness = yellow socket on and at the same time red LED extinguishing = red socket off,
yellow LED extinguishing = yellow socket off and at the same time red LED brightness = red socket on
3 Input AC220V,press the yellow/red label button of the remote-controller ，the yellow/red knob PWM settings will be effective, and the yellow/red socket will have the PWM output.
Rated input AC230V (built in 250V2A Fuse)
Yellow socket output AC230V 600mA ,Red socket output AC230V 600mA.
After input AC230V, the yellow-red socket is still Electrification when they are off,
at this time one pole is continuously on, and the other is off by the high resistance .
Don't touch the metal part of the input & output socket.
The remote-controller must aim at the remote- receiver , and the remote-controller distance is 5 meters.
Yellow output of PWM can only be obtained until by pressing the yellow label button of the remote-controller, and Red output of PWM can only be obtained until by pressing the red label button of the remote-controller.
We can customize DC input & output DC PWM, or max-power PWM, outlet length, international voltage pin or socket
NKAC150Y (remote control) standard configuration 2 flat pin input AC230V 50/60HZ (250V 2A Fuse)
Output 2 flat sockets ,yellow socket output AC230V 50/60HZ 800 mA ,
red socket output AC230V 50/60HZ 800 mA (including output socket line length 75 mm)
Controller size (not include input pin)length 98x wide 54x high 35mm,
pin length 35x wide 20x high 25mm controller weight (includes pin socket)300g
Hａnd held remote-controller input DC DC3V =AAA-1.5V battery X 2.
Handheld remote controller weight (includes battery) 200g
size length 105x width 40x high 15mm
Content Disclaimer All information in this document may be changed without notice. All information in this document should not be regarded as a commitment of NKAUTOMATIC. NKAUTOMATIC. is not responsible for any mistakes that may occur in this article.
Copyright@ NKAUTOMATIC.COM. all rights reserved.
服務咨詢：
儀表技術群：
