絕緣電氣強度擊穿電壓試驗儀結構原理及性能特點：
1、主要由升壓系統、測量系統、A/D轉換器、放電系統、電極、油箱、電極定位架、計算機數據處理系統、軟件等組成；
2、計算機---A/D轉換器---測量控制系統---調壓裝置---升壓變壓器---試樣；
3、高壓變壓器主要產生試樣所需的直流電壓；
4、調壓器用于調節升壓變壓器輸入端電壓以產生高壓所需的輸入電壓；
5、電壓測量主要是從高壓變壓器測量端測量，高壓變壓器測量端和高壓端是線性的；
6、放電系統在試驗做完以后放電，以免產生放電對人身的危害；（當試驗結束后，機器部件仍可能存在殘留的高電壓，此殘留電壓足以對人產生致命的傷害，配備此棒，完好的解決此安全隱患）。

絕緣電氣強度擊穿電壓試驗儀技術參數

1 試驗變壓器

1.1 輸出電壓： AC  0-10000V，DC 0-10000V；

1.2 輸入電壓：220v

1.3 額定容量下，長期連續運行；

1.4 zui大輸出電壓下，PD≤1pC；

1.5 噪聲≤58dB（1m位置測量）。

2 調壓器

2.1 輸入電壓：220V；

2.2 額定容量：2kVA（如果有補償，可以小于15kVA，但不小于10kVA）；

2.3額定容量下，長期連續運行；

2.4噪聲≤58dB（1m位置測量）;

2.5 電動調壓。

3 高壓分壓器

3.1 高壓臂電容：1nF；

3.2 分壓比：700（可討論，結合測量控制系統）；

3.3 額定容量下，長期連續運行；

3.4 zui大輸出電壓下，PD≤1pC；

3.5 測量精度：1%。

4 計算機控制

4.1 藍牙連接；

4.2 安全保護；

5 試驗電極

5.1 滿足GB/T 1408-2006 絕緣材料電氣強度試驗方法；

5.2 滿足GB/T 1695-2005 硫化橡膠工頻電壓擊穿強度和耐壓強度試驗。

絕緣電氣強度擊穿電壓試驗儀適用材料：

    主要適用于固體絕緣材料如下：

電線套管、

樹脂和膠、

浸漬纖維制品、

云母及其制品、

塑料薄膜、

陶瓷、

玻璃、

絕緣漆、

硫化橡膠、

電纜紙、

絕緣漆漆膜、

硬質橡膠、

紙板等絕緣介質在空氣或液體介質中，測量工頻（48~62Hz）或?qū)?yīng)直流電壓下?lián)舸姸群湍碗妷簳r間。

適用于連續均勻升壓或逐級升壓的方式，對試樣施加交流/或直流，電壓直至擊穿，測量擊穿電壓值，計算試樣的擊穿強度；用迅速升壓的方法，將電壓升到規定值，保持一定的時間試樣不擊穿，定此時規定值為試樣的耐電壓值。

絕緣電氣強度擊穿電壓試驗儀技術指標：

輸入電壓： 交流 220 V    輸出電壓： 交流 0--100 KV ;/直流 0—100 KV

電器容量： 10KVA   高壓分級： 0-100KV    升壓速率：0.01-5.0kv

              （備注：滿足標準要求并可以根據用戶需求設定不同的升壓速率）

06、試驗方式： 交流試驗/ 直流試驗：1、勻速升壓  2、梯度升壓 3、耐壓試驗

試驗介質：空氣，試驗油    安裝靈敏度較高的過電流保護裝置保證試樣擊穿時在0.05S內切斷電源。    儀器配備的故障報警系統 避免用戶操作故障儀器發生危險。（上位機報警和下位機報警）

絕緣電氣強度擊穿電壓試驗儀

使電介質擊穿的電壓。電介質在足夠強的電場作用下將失去其介電性能成為導體,稱為電介質擊穿,所對應的電壓稱為擊穿電壓。

電介質擊穿時的電場強度叫擊穿場強。不同電介質在相同溫度下,其擊穿場強不同。當電容器介質和兩極板的距離d一定后,由U1-U2=Ed知,擊穿場強決定了擊穿電壓。擊穿場強通常又稱為電介質的介電強度。

提高電容器的耐壓能力起關鍵作用的是電介質的介電強度。附表為各種電介質的相對介電常量εr和介電強度。電介質εr擊穿場強,×106/（V·m-1）

Breakdown voltage insulation dielectric strength tester structure principles and performance characteristics:
1, mainly by the booster system, measuring system, A/D converter, discharge system, electrode, fuel tanks, electrode positioning, computer data processing system, software, etc;
2 - A/D converter, computer measurement control system - - - - regulating device step-up transformer - sample;
3, high voltage transformer is mainly produce samples required dc voltage;
4, voltage regulator is used to adjust the step-up transformer voltage of the input to generate the input voltage to high voltage;
5, voltage measurement mainly from high voltage transformer end measurement, high voltage transformer is linear measurement end and high end;
6 finish after discharge, discharge system in the test, lest produce discharge of bodily harm; (when the experiment ended, the machine parts are still there may be residual high voltage, the residual voltage is enough to cause fatal damage to people, equipped with the rod, solve the potential safety hazard of intact).
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage technology parameters
 
1 testing transformer
 
Output voltage: 1.1 AC 0-10000 - v, DC 0-10000 - v;
 
1.2 the input voltage: 220 v
 
1.3 under the rated capacity, long-term continuous operation;
 
1.4 under the maximum output voltage, PD 1 PC or less;
 
1.5 noise 58 db (1 m position measurement) or less.
 
2 voltage regulator
 
2.1 the input voltage: 220 v;
 
2.2 nominal capacity: 2 kva, if any compensation, can be less than 15 kva, but not less than 10 kva);
 
2.3 under the rated capacity, long-term continuous operation;
 
2.4 noise acuities were 58 db (1 m position measurement);
 
2.5 the electric voltage regulation.
 
3 high voltage divider
 
3.1 high pressure arm capacitance: 1 nf;
 
3.2 compression ratio: 700 (can be discussed, combined with measuring control system);
 
3.3 under the rated capacity, long-term continuous operation;
 
3.4 under the maximum output voltage, PD 1 PC or less;
 
3.5 accuracy: 1%.
 
The computer control
 
4.1 bluetooth connection;
 
4.2 safety protection;
 
5 test electrode
 
5.1 meet the GB/T 1408-2006 insulation dielectric strength test method;
 
5.2 meet the GB/T 1695-2005 rubber power frequency voltage breakdown strength and compression strength test.
 
 
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage applicable materials:
 
Mainly suitable for solid insulating material is as follows:
 
The wire casing,
 
Resin and rubber,
 
Impregnated fiber products,
 
Mica and its products,
 
Plastic film,
 
Ceramics,
 
Glass,
 
Insulating paint,
 
Vulcanized rubber,
 
Cable paper,
 
Insulating varnish film,
 
Hard rubber,
 
Cardboard in air or fluid medium, such as insulating medium measuring power frequency (48 ~ 62 hz) or the corresponding breakdown strength under dc voltage and voltage withstａnd time.
 
 
 
Apply continuous uniform booster or booster way, step by step toward a sample dc, ac/or until the breakdown voltage, breakdown voltage measurement, calculation of sample breakdown strength; Use the method of rapid booster, e., will increase the voltage to maintain a certain amount of time the sample breakdown, not set the withstａnd voltage value of the specified value for sample and now.
 
 
 
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage technical indicators:
 
The input voltage: ac 220 V output voltage: communication 0-100 KV; / dc 0-100 KV
 
Electric capacity: 10 kva high-pressure sizing: 0-100 kv step-up rate: 0.01 to 5.0 kv
 
(note: meet the standard requirements and can be set according to user requirements of different rate of pressure rise)
 
06, test method: ac/dc test: 1, 2, gradient booster 3 uniform booster, withstａnd voltage test
 
Test medium: air, oil test installation high sensitivity of over current protection device to ensure the sample breakdown within 0.05 S when cut off power supply. The instrument is equipped with advanced fault alarm system Avoid user operation fault instrument. Alarm (the upper machine and lower machine alarm)
 
 
 
 
 
 
 
 
 
 
Insulation dielectric strength tester breakdown voltage
 
The dielectric breakdown voltage. Dielectric under the action of electric field in a strong enough will lose its dielectric properties become the conductor, called the dielectric breakdown, the corresponding voltage is called the breakdown voltage.
 
When the dielectric breakdown electric field intensity is called breakdown voltage. Different dielectric under the same temperature, the breakdown voltage is different. Capacitor medium and the plates, after a certain distance d by U1 - U2 = Ed, breakdown voltage determines the breakdown voltage. Dielectric breakdown voltage is often called the dielectric.
 
Increase the ability of condenser pressure is dielectric plays the key role of dielectric strength. Schedule for all kinds of dielectric epsilon r relative dielectric constants and dielectric strength. Dielectric breakdown field strength epsilon r, x 106 / (v. m - 1)