UV-Integrator 140

The UV-Integrator 140 is a high quality UV measuring instrument. It is used to measure UV energy of different light
sources, especially on printing machines. It was specially designed with a recess in the housing for better handling.
It is ideal to ensure quality control of printing and drying processes.
Big size, heavy duty pass-through Integrator with a diameter of 140 mm. It is reliable and simple to use.
The UV-Integrator 140 is available in six different measuring ranges*:
(Please state upon order)
Item 9.1 UV-Integrator 140, Type 1, Diazo 350 – 460 nm
Item 9.2 UV-Integrator 140, Type 2, UV-A 315 – 400 nm
Item 9.3 UV-Integrator 140, Type 3, UV 250 – 410 nm
Item 9.4 UV-Integrator 140, Type 4, UV-B 280 – 315 nm
Item 9.5 UV-Integrator 140, Type 5, UV-C 230 – 280 nm
Item 9.6 UV-Integrator 140, Type 6, UV-V 395 – 445 nm
*further spectral ranges available upon request
By addition of the incidence of the light quantities during the exposure cycle, relative values are calculated.
Because of uneven radiation distribution of the UV light source and different type of construction of the measuring
devices by different manufacturers, different readings may appear under the same measurement conditions.
Technical Data:
Spectral range: UV 250 – 410 nm
Measuring range: 0 to 5,000 mW/cm²

Display: 6-digit LCD
Display range: 0 to 999,999 mJ/cm²

Power source: long life 3.6 V Lithium Battery
Power consumption: 100 µA
Battery service life: 10,000 hrs
Dimensions: ∅ 5.5” (140 mm) height ½” (13 mm)
Weight: approx. 16 ounce (450 grs.)
Temperature range: 0 to 45° Celsius
Heat protection: Heat shield on back plate
Base Accuracy: ± 5 %

While on the conveyer belt, the UV-Integrator 140 can withstand max. 110° C / 230° F for up to 10 seconds. The
temperature of the housing should not exceed 45° C / 113° F.

Calibration:
In order to keep its full function and precision it is recommended to have re-calibration done once per year. Recalibration will also be necessary after change of battery. Ongoing, PTB traceable calibration with certificate
Warranty:
2 years from the date of purchase, For the German quality battery we guarantee one year

德國UV能量計 UV-Integrator140 UV能量計大陸總代 原裝* 謝絕講價！！

德國UV能量計是用于測量曝光裝置的UV能量的一種儀器，測量儀的主感器在測量儀的背面，測量范圍為250~410納米，測量時可直接顯示于UV能量計正面的顯示屏上讀出（單位：毫焦耳/平方厘米），該UV能量計的電源為3.6伏特的鋰電池，該電池由于使用了特別的能源節省線路，該電池可持續大約10000小時。

技術數據：

德國UV能量計（UV-integrator1401）

尺寸：直徑140mm*高13mm　　　　　

重量：約450g

適用設備：UV紫外線干燥機、曝光機　　　

測量范圍：0-5000mW/cm²

能量顯示：LCD 0-999999mj/cm²

電源： 鋰電池3.6V 

測量范圍： 250-410nm(光譜圖波長)

耗電量： 約10000小時（Lithiwn鋰電池）

工作溫度（℃）： 0～70℃

UV能量計在輸送帶上耐溫110℃不超過10秒

使用/操作：

a． 打開ON開關，則LCD（顯示屏）是顯示為零。

b． 將UV能量計放置于曝光UV燈源附近,以其背面對準燈源（UV能量計的能量感受器在背面）。

c． 直到UV能量計的顯示屏上有測量顯示，例如800毫焦耳/平方厘米。(800mj/cm²)。

d． 將顯示屏的值記錄或作為品質控制與實驗參數，關掉UV能量計開關(OFF)。