德國奧萊斯OLES進口低溫止回閥

【進口低溫止回閥】結構說明：

低溫止回閥的閥瓣呈圓盤狀，繞閥座通道的轉軸作旋轉運動，因閥內通道成流線形，流動阻力比升蝶式止回閥小，適用于低流速和流動不常變化的大口徑場合，但不宜用于脈動流，其密封性能不及升降式。蝶式止回閥分單瓣式、雙瓣式和多半式三種，這三種形式主要按閥門口徑來分，目的是為了防止介質停止流動或倒流時，減弱水力沖擊。;低溫止回閥瓣沿著閥體垂直中心線滑動的止回閥，內螺紋止回閥只能安裝在水平管道上，在高壓小口徑止回閥上閥瓣可采用圓球。

The disc of cryogenic check valve is disc-shaped and rotates around the rotating axis of the seat passage. Because the inner passage of the valve is streamlined, the flow resistance is smaller than that of the lifting butterfly check valve. It is suitable for large caliber situations with low flow rate and unstable flow, but it is not suitable for pulsating flow, and its sealing performance is inferior to that of the lifting butterfly check valve. Butterfly check valves are divided into three types: single-lobe, double-lobe and multi-half. These three types are mainly divided according to the valve caliber. The purpose is to prevent the hydraulic impact when the medium stops flowing or backflows. Check valves with low temperature check discs sliding along the vertical center line of the valve body. Internal threaded check valves can only be installed in horizontal pipelines, and discs with balls can be used on high pressure small caliber check valves.

【進口低溫止回閥】詳細說明

蝶式止回閥的閥體形狀與截止閥一樣(可與截止閥通用)，因此它的流體阻力系數較大。其結構與截止閥相似，閥體和閥瓣與截止閥相同。閥瓣上部和閥蓋下部加工有導向套簡，閥瓣導向簡可在閥盞導向簡內自由升降，當介質順流時，閥瓣靠介質推力開啟，當介質停流時，閥瓣靠自垂降落在閥座上，起阻止介質逆流作用。直通式蝶式止回閥介質進出口通道方向與閥座通道方向垂直；立式升降式止回閥，其介質進出口通道方向與閥座通道方向相同，其流動阻力較直通式小。低溫止回閥：閥瓣圍繞閥座內的銷軸旋轉的止回閥。碟式止回閥結構簡單，只能安裝在水平管道上，密封性較好。低溫止回閥：閥瓣沿著閥體中心線滑動的閥門。管道式止回閥是新出現的一種閥門，它的體積小，重量較輕，加工工藝性好，是止回閥發展方向之一。但流體阻力系數比旋啟式止回閥略大。此外，還有—些不適用于泵出口安裝的止回閥，如底閥、彈簧式，Y型等止回閥。低溫止回閥用途和性能規范。本閥門用于工業管道上作阻止介質逆流的裝置。  

【進口低溫止回閥】用途：

依靠介質本身的流動而自動開、閉閥瓣，防止介質倒流。低溫升降式止回閥適用于甲烷、液態天然氣、乙烯、二氧化碳、液氨、液氧、液氮、液氫等低溫介質。低溫閥門嚴格控制材料的化學成份及低溫沖擊韌性等力學性能指標。  低溫升降式止回閥參數：公稱壓力：1.6Mpa、2.5Mpa、4.0MPa適用溫度：-196℃～+80℃公稱通徑：10mm～250mm主體材質：閥體： CF8閥桿、閥瓣： 不銹鋼填料、密封圈： 聚四氟乙烯